潤滑脂滴點檢測流程

 1、檢查儀器中油浴界面是否符合要求，儀器運轉是否正常，填寫試驗臺賬;2、儀器正常后開始試驗，填寫原始記錄表頭部分;3、調節溫度計位置，使浴中的溫度計水銀球位置與試驗試管中溫度計的位置高度在一一個水平面上;4、取試樣(不能取表面試樣)將試樣裝滿脂杯用刮刀除

去多余試樣。從杯底小孔將金屬棒插入，旋轉向上伸出，帶出試樣，將帶出試樣去除，使脂杯內側留下厚度可重復的光滑脂膜;5、將脂杯和溫度計放入試管中，把試管掛在油浴中。使油面距試管邊緣不超過6mm;6、開啟電源開關，攪拌油浴，按4-70C/min的速度升溫，直到油浴溫度比預期滴點約低170C的溫度。然后降低加熱速度，使試管里的溫度與油浴溫度差值在20C或低于20C范圍內，繼續加熱，以1-1. 50C/min的速度加熱油浴，使其溫度差維持在1-20C之間。當溫度繼續升高試樣逐漸從脂杯中露出從脂杯中滴出滴1滴流體時，立即記錄兩個溫度計上的溫度。兩個溫度計讀數的平均值即為測試結果;7、填寫原始記錄及化驗報告單;8、清理試驗臺面及儀器。